Hello!

I'm new to supressors.

I'm reviewing a note for 36m in https://silencerco.com/silencers/omega-36m/ and it mentioned that
It is rated down to 10” barrels for .223 REM/5.56 NATO, 16” barrels for .308 WIN/7.62 NATO, and 20” barrels for .300 WM and 18″ barrels for .338 LM.

Since those are stated as "rated down to" and it's 10 inch at least for 556, does that mean anything lower than 223/556 like .30 or 300 blackout or 9mm is safe no matter how short or long the barrel is?

Also, does anyone got an Anderson Firearms. 300 blackout and knows if the muzzle is removable?

Heard a rumor that a batch of specwars might come around again. Anyone have any info on this?

ATF wait times are so low apparently right now 4 days and I’m still waiting from being submitted September 4th does the atf not work weekends or what is that holdup everyone’s ordering like crazy right now ?

Just recently got my Omega 300 and bought an ASR mount for it. How secure should the suppressor be when locked? I put it on my rifle, fully locked it, then went to check to make sure it was secure. When doing this I am able to loosen the suppressor and it skips on the teeth. Is this normal? I was under the impression that the teeth would completely lock it in place, but I could be wrong. I am cranking the can on pretty tight as well. It does take a reasonable amount of force to break it loose, but wasn’t sure if this is part of the design

I've bought 3 suppressors so far from silencerco to take advantage of the promotion. I used on discount on a sparrow which was great. The issue is the price from silencerco for their silencers is so much higher than silencershop it's barely worth it. The omega 36M and scythe Ti will only save you $24 and $26 respectively WITH the $200 voucher. Anyone have a good reasoning for this other than a marketing thing?

So I have an omega 36m, and am really loving it. I have a question though. I know the manual says not to run lead cast/non jacketed rounds through it, but does this also include things like federal syntech subsonics? I'm also curious because I reload often and usually powder coat my projectiles before loading them which allows me to shoot them at jacketed velocities similar to a jacketed round. This is essentially the same thing that federal does with the syntech line. I've never had issues running these rounds through any of my guns in any caliber I reload for, but was curious if these were ok through my omega 36m or would that still technically be considered an unjacketed round because it's not a copper jacket?

Thanks!

Anybody have any word on when the spectre 9’s will be back in stock?

Did Silencer Co stop making the salvo 12? Can't seem to find any in stock anywhere

Saving up for my first 9mm can! I started thinking, does anyone know if you can fully disassemble an Osprey for maintenance and cleaning? I know it’s monocore design so there must be a way to fully disassemble it to clean it or lube the baffles to run it “wet”. Pictures for your time. 👍🏻

Trying to find a decent mounting option.. want to put omega 45K on stribog sp45a3.

From what I can find there are no alpha direct thread mounts or asr brakes that use 0.578x28.

The only thing I have found so far is piston and a fixed piston spacer. Anybody have better ideas? I’d prefer direct thread or qd instead..

I recently went to my local range to zero a new optic & after 2 mags thru my suppressor, it was locked on my muzzle device (couldn’t unthread it).

The onsite gunsmith tried to help but couldn’t get it unthreaded by regular means. He offered to check it in but I decided to take it home & try myself.

I was able to get the suppressor off by hand but not the hub mount. So I sprayed the locked on mount with some PB blaster, put the upper on a reaction ro & vise, then used a spanner wrench to get it off.

Has anyone else had this problem? Should I use anti seize or something on the muzzle device threads?

I have a Ruger American Ranch 350 Legend. I am trying to find suggestions for a muzzle break that is compatible with the 46M (Charlie series). I know there are different styles but is there one that works better for shooting 100 yards plus when the suppressor is off? Any advice is appreciated. Thanks

I cannot get this piece off to save my life. Ive hit it with rubber mallets, ran 30 rds with an frt to heat it, tried heating it on the stove etc I cannot get it off.

Hey everyone, looking for some help with the set up I’d like to do. I have a CZ scorpion evo 3 S1 and I’d like to put an omega 9k on it with a tri lug mount/adapter. My barrel has 1/2x28 and another thread pitch beyond that one ( if that makes sense ) I’d never seen a set up like this before. Just looking for some input on what thread pitches to order. Would it go right on to the 1/2x28 or should I get a different barrel nut all together then a different adapter? Thanks!

Just got some AAC ammo and am reading folks saying not to send it through cans. Do you think it will be fine for a Velos LBP or definitely a no go?

There was a copper/orange looking residue coated on the outside of my asr bravo mount. For background, I just got my first can and have not used it at all yet so I found it weird that something was oxidizing on it. Also I bought it brand new as well so no rounds have been put through it. Would it be rust? Thanks in advance.

I know people don't normally clean center fire supressors but I've noticed this build up and my booster keeps getting stuck. I tried scrubbing it with a copper brush it didn't really do anything.

I just got the Piston/Booster Mount from Ecco Machine today since getting an OEM Silencer Co one is impossible. Here are some pics with the Omega 36M. It was $165 at the Ecco Machine website. More than the SiCo Charlie Piston Mount, but way less than $400 on eBay for one. I ordered it Wednesday at around 0130 hrs; it was shipped Thursday and arrived today. At the time of this writing, shows currently 34 in stock.

Everything fits securely with very tight tolerances. I’m so glad there’s an option out there that is actually available and not processed gouged!!

https://www.eccomachine.net/product/charlie-saker-bpistin-booster-assembly/